Home House & Components Fixtures Countertops
Updated: Jun. 09, 2023
You are watching: A Full Guide to Countertop Installation
Prefab laminate countertops
Plastic laminate countertops have been adorning kitchen cabinets for more than 50 years—and with good reason. Plastic laminate is a tough, durable material that comes in hundreds of colors and finishes. When applied to particleboard or plywood underlayment by a production shop, this proven product is ideal for kitchens, bathrooms and other settings. By installing premade countertops yourself, you’ll save 50 percent of what a professional installer would charge. Want to add natural flair to your kitchen? Learn how to install butcher block countertops.
In this article, we’ll show you how to measure, buy and install your own countertops. Our instructions include how to make chip-free cuts, tight-to-the-wall scribes and nearly invisible joints for a professional looking job.
The easiest approach is to order custom-made laminate countertops (ours cost about $30 per running foot) from a local home center, full-service lumberyard or cabinet/countertop shop. You can also buy premade take-it-with-you stock tops (in limited colors) at many home centers, for about half the price of custom countertops. Shop for the latest in plastic laminates on manufacturer Web sites.
You can also view product samples at home centers and countertop suppliers.
Measure carefully before you order your new prefab laminate countertops
Before ordering new countertops, you’ll need to make accurate measurements of your cabinet layout. A word of warning here: If you have a U-shaped kitchen with two large miters and have never installed countertops before, you may want to hire a pro. Configurations like this require you to scribe three walls at one time. But if you have only one inside corner as we did, the project is well within the skill level of the average do-it-yourselfer.
Make a sketch and then, starting from the back walls, measure the exact lengths from the walls to the edge of each run of cabinets. Add 3/4 in. to the length of each section to allow for overhangs. Allow an extra inch to protrude into a freestanding range space. You’ll trim it off later for an exact fit (Photo 11). Order a laminate end cap (or make your own, Photo 12). If you need to butt the countertop into a side panel like a pantry or refrigerator cabinet, add an extra 1 in. for notching (Photos 14 – 16). This will give a more finished look than a straight cut. Also measure the depth of your base cabinets. Standard laminate tops are 25 in. deep. Check to make sure you’ll have at least 1/2-in. overhang beyond all the drawer fronts.
Most manufacturers will supply preshaped and preglued iron-on end caps to cover finished ends, but I prefer to order a little extra plastic laminate that I can score and cut and glue into place with contact cement for a longer-lasting grip. Either system works fine, but if this is your first go at this type of project, you’ll find the iron on end caps easier to install. Just keep in mind you’ll need to do a bit of filing in either case to shape the end caps. Another important consideration is corner and edge style. To fit our design requirements, we chose square corners for all our edges. If you want any rounded corners on exposed edges, discuss this with your supplier ahead of time and ask to see sample profiles.
Read more : Why Not to Use Drano to Unclog Your Drains
You’ll also need build-up strips (usually 3/4 in.) (Photo 2) to support the top across the cabinets. At first glance, countertops appear to be 1-1/2 in. thick, but the substrate that the laminate is glued to is actually just 3/4 in. thick, as the underside reveals. Applying additional build-up strips to the top of your cabinets will fill the void at support points and elevate the countertops above top drawers. When ordering, ask for build-up strips, but keep in mind you can easily make your own from scrap 3/4-in. plywood or 1×2 pine.
Once you complete your measurements, take your drawing to your countertop supplier and discuss your plan to make sure you’ve covered all the bases. If you don’t have a home center near you or your lumberyard doesn’t provide this service, check the internet for “Countertops.” When you place your order, ask about delivery to your home. In most cases, the odd shapes are unwieldy and won’t rest securely on top of the family car.
Scribing your backsplash to the wall is the most crucial step
You can start with any section of countertop, but it’s best to begin with the longest corner section because the other sections often join or relate to this piece. Our long section had a number of fitting challenges—especially the corner. To get an accurate scribe to the wall here, you need to temporarily join the corner (Photo 5).
To do this, install the miter bolts as shown in Photo 5 and then slide the top into the corner for a test fit. Before you scribe, align the front edges of the countertop parallel to the cabinet fronts. Close gaps where the backsplash meets the wall if possible. Scribe the top as shown in Photo 6. Keep in mind you can remove up to 1/2 in. from the backside of the backsplash to fit your wall. This is more than enough in most cases, so don’t panic if your adjoining wall looks out of whack.
Next, sand down the back edge (Photo 7) of the backsplash to your scribe line with a belt sander. Tip the belt sander slightly to undercut the backsplash for a tighter fit. Set the countertop back against the walls and check it for fit. It should fit on the first try, but you may need to do some additional sanding for a tight fit.
Next, remove the miter bolts and separate the sections so you can cut the sink opening (Photos 8 – 10).
Tip: Be sure you have a build-up strip under the backsplash behind the sink and at each side of the sink base cabinet. The full weight of the sink needs continuous support.
Use a handsaw to cut the countertop to length
Before we could assemble the miter joint, we had to cut the short section of the countertop exactly flush with the cabinet end (Photo 11) to make room for the range. If you’re skilled with a circular saw, you can make this cut from the underside with a 40-tooth carbide blade, but it’s risky. One false move and you’ve got another workbench top! Why take chances? A sharp handsaw will give you a nice, slow, controlled cut and time to react if the cut is straying from your mark. Use a traditional saw that cuts as you push the blade away from you. Press masking tape over the area you plan to trim.
The masking tape serves a dual purpose here: It lets you easily see your pencil mark and it reduces chipping of the laminate as you cut. After the cut, use a belt sander to sand right to the line. Make sure you’ve made a square edge. Next, glue a build-up strip to the bottom flush with the newly cut edge and clamp it in place.
Once the glue is dry, you can apply matching plastic laminate over this built-up edge. If you don’t have a precut end cap, cut one from your extra piece of laminate. Make a couple of practice cuts with a laminate cutter (Photo 12) before you try the real thing. Set your laminate on scrap wood (not on your new countertop!) and draw the shape of the end cap plus 1/4 in. extra on both the top and front.
Read more : Hell’s Kitchen: What Happened To Season 3 Winner Rock Harper
Score the top several times to cut through the laminate, using a straightedge as a guide. Be careful near the corner where the backsplash section leaves a right angle rise. It’s easy to break this little chunk off.
Apply contact cement to each mating surface and let it dry to the touch (about 20 minutes). Then position the end cap even with the bottom edge of the build-up filler strip and press it firmly into place.
Using a dry rag, firmly wipe the surface to further press it for a good bond. Now file the end cap flush to the countertop (Photo 12). Take your time with slow, controlled strokes. When the edge is almost flush, slightly bevel the end cap to remove sharp corners that could snag a dishcloth later. Finally, push the sections back together, apply caulk and join the miter (Photo 13). Then install the miter bolts using the method shown in Photos 4 and 5.
Cutting a return
You may not have to make a “return” cut in your countertop like the one shown in Photos 14—16. If you do, follow the photo sequence. Then cut and glue a small piece of laminate to the exposed edge.
Although we made the countertop flush with the cabinet side (to accommodate the range, Photo 14), you may have to adjust your scribe to allow for an overhang (Photo 15).
Use steel angles to anchor the top
Professional installers vary greatly in their methods of fastening countertops to base cabinets. Some just glue them down with construction adhesive, while others screw through the cabinet corner braces or sides into the top. Using 1-1/2 in. steel angles like those shown in Photo 17 is foolproof and simple.
You can buy them at any hardware store, but don’t use the screws provided. Instead, buy 5/8-in. long No. 8 screws. I like to place them a hair lower than the top of the cabinet (or build-up) and then draw the top down tight with a screw into the underside of the countertop. Use as many angles as it takes to get a solid installation. Figure on using four every 3 ft.
Required Tools for this premade countertops project
Have the necessary tools for this DIY project lined up before you start—you’ll save time and frustration.
- 4-in-1 screwdriver
- Belt sander
- Caulk gun
- Circular saw
- Clamps
- Cordless drill
- Drill bit set
- Dust mask
- File
- Handsaw
- Hearing protection
- Jigsaw
- Safety glasses
- Scribing tool
- Straightedge
- Tape measure
You’ll also need a specialty tool: a laminate cutter
Required Materials for this premade countertops project
Avoid last-minute shopping trips by having all your materials ready ahead of time. Here’s a list.
- 1-1/2 in. steel angles
- 1-1/4-in. drywall screws
- 5/8-in. long No. 8 screws
- 80-grit sanding belts
- Acrylic caulk
- Masking tape
- Miter bolts
- Premade cabinets
- Silicone caulk
Source: https://gardencourte.com
Categories: Kitchens