How to Remove a Moen Kitchen Faucet

If you have a cartridge faucet in your home, there’s a good chance it’s a Moen faucet. When it comes to faucets, this U.S-based brand is a household name known for its quality. Still, sometimes faucets break, or you want to renovate your home, which means removing and replacing your faucet.

Removing most faucets is relatively easy, but each one follows its own removal process. We can help you ensure that you take the right precautions to avoid problems like leaks or further breakage.

You are watching: How to Remove a Moen Kitchen Faucet

We have the solutions you need for all your Moen kitchen faucet repair so you can get your sink working right without causing damage to other parts of your home.

Moen’s Faucets: How to Repair Like a Pro

If you have a leak, you should remove and repair your faucet as soon as possible so you don’t have to deal with the water ruining your cabinets, flooring, or even leaking into your basement. Luckily, when it comes to Moen kitchen faucets, repair requires minimal tools, and you may be able to do it yourself. All you need is a screwdriver, needle nose pliers, and a wrench.

Follow the steps below before you make repairs:

Step 1: Shut off the waterline

Before you start the removal process, find the waterline supply, and close the valve. Most homeowners have separate valves for cold and hot water, so make sure to shut them both off.

Step 2: Dry the pipes

Before you start repairing Moen kitchen faucets, you need to make sure the pipes are empty. Open the sink valve to see if you have any water left in the pipes and drain them if so. Without draining the pipes, you risk that water draining onto your floor or into your cabinets and pausing your project to clean up the mess.

Step 3: Extract the faucet’s Handle

Use your screwdriver to remove the handle. Once you remove it, you will see a set screw attached. Use the wrench to unscrew it, and then take the handle off slowly and carefully.

Step 4: Take out the plastic part

Read more : 7 Modern Kitchen Design Trends Stylishly Incorporating TV sets into Kitchen Interiors

Now that you’ve taken off the handle, you can see whether you have a major leak, a malfunctioning rubber gasket, or something else. You will notice a small dome and a jacket that you must pull out with a wrench. Start turning the wrench, and the parts will slide out.

Step 5: Take out the mechanism

Once you’ve removed the plastic sleeve, you can take out the handle mechanism. The handle mechanism controls the waterline flow, so handle it with care to avoid damaging it.

You will notice that a screw secures the mechanism to the sink. Use your screwdriver to loosen the screw and then take out the mechanism.

Step 6: Take off the white ring

Once you’ve removed the mechanism, you can take off the white ring under it. When removing the ring, take care to keep it in a place you can find it again because you’ll need it again later when you set up a new faucet or put your old one back in. Under the ring, you’ll find a washer that you also need to remove.

Step 7: Lift the spout

If you’ve followed the previous steps carefully, you’ll have no trouble lifting and removing the spout. At this point, you should write down the part’s directions and in which order you’ve removed them to make it easier to put back together later.

The spout part will come off without any tools. Under the spout, you’ll find a clip. Take off the clip using a screwdriver. If you have an old faucet, you’ll also have to take off the cartridge. Hold the stem using pliers and spin the faucet until it loosens. If pliers don’t help, you may have to use a cartridge puller.

After you complete the removal, assess the situation, and prepare for your Moen faucet repair. Kitchen faucet repair uses the same tools, so if you successfully removed yours, you can put it back in, too.

Reinstalling Your Faucet

Now that you’ve disassembled the faucet, inspect it for possible damages and determine the problem. If you see breaks or unusable parts, you may have to replace the valve.

Once you’ve gotten the right parts, you can begin your kitchen faucet repair. The company makes it easy to reinstall your appliance, so as long as you remember how to replace the parts, you shouldn’t have a problem.

How to Install a Faucet

Read more : What does it cost to remodel a kitchen?

Installing new faucets is as simple as removing them. If you follow these instructions, you can have a working sink again quickly.

Place the plastic gasket, rubber cap, or trim ring over the empty hole in the sink. Don’t forget to follow the manufacturer’s instructions on how to proceed with the installation. If you learn visually and don’t have experience installing faucets, you may also want to watch a YouTube video.

Turn on the video’s volume and follow the instructions. Once you finish, exit fullscreen to focus on your sink project.

You can also find affiliate links that will help you find the right tools and parts you need to complete the repair process. These affiliate links will bring you to excellent sources for tools, parts, and additional equipment to make the installation easier.

Position the faucet handle into the sink hole. Install washers under the sink and dry the area to prepare for the next step. Attach the sprayer hose to the main supply pipe.

Next, pull down on the hose, and add the weight. Remember that the weight needs enough of a gap to hang freely. Connect the water supply lines and use plumber’s tape to help secure them if needed.

Never tighten the supply lines as they may burst and cause damage to your sink. Turn the water and watch out for leaks. If you don’t see any, take off the aerator, and open the valve to clear the lines.

Repairing faucets can seem intimidating to many people, especially if you’ve never done it before. Despite these simple steps, there are no keyboard shortcuts that can help you fix the damage in your bathroom, home office sink, or main dining area.

If removing, replacing, and installing faucets seems like a complex project to you, call a professional plumber to help out. An experienced plumber will inspect the situation, find the cause of the problem, and offer a quick solution.

If you need a replacement, you may find the selection of faucets overwhelming. Mr. Kitchen Faucets can help you streamline the process and work with you to choose the right appliance for your home. We know which ones work best in different home environments, and we’re here to answer all your questions.

Source: https://gardencourte.com
Categories: Kitchens