Categories: Kitchens

Six Simple Steps for Replacing Tile

Published by
James marcus

Sometimes all it takes to crack a tile is dropping a hairbrush or an aerosol can of deodorant in just the right way, but don’t worry – replacing a tile is easier than you think. All you need is a new tile, the right tools, and an hour of your time, and your floors will look as though no damage occurred. Plus, you will avoid the high price a professional would charge.

Note: If you’re only replacing one or two broken tiles, I recommend using a pre-mixed thin-set mortar and pre-mixed grout to cut down on the time needed to complete the repair. All buckets have a “recommended for” or “use with” list of tile types, so be sure to check the label to match your tile type with the pre-mixed thin-set before you purchase.

Step 1: Remove the Grout

Start by scraping away the old grout with a back-and-forth motion along all sides of the broken tile with a grout saw or grout remover tool.

Step 2: Remove the Tile

For this step, you will need to put on safety glasses and durable gloves because it is about to get messy. Use your hammer to break up the tile into smaller pieces. Carefully remove the pieces and discard them. You want the surface under the tile to be as smooth as possible before setting the new tile. Use a hammer and chisel to remove the old thin-set from the floor. Once your area is thoroughly chiseled off, use a vacuum to clean up the remaining dust and debris.

Step 3: Lay New Thin-Set

Using the flat edge of a notched trowel, scoop a liberal amount of pre-mixed thin-set and spread it onto the bare, clean floor. Notching tile allows air to escape when you lay down the tile. If there are pockets of air under the tile, water and mold can gather. Notches ensure complete coverage and stronger bonds between the tile and the floor.

Now use the edge of the notched trowel to create evenly spaced, parallel ridges in the thin-set. For most tiles, you will need a 1/4″ square or U-Notched trowel to make a good bond between the new tile and the floor. For the best adhesion to your floor, always spread thin-set on the back of the tile for the maximum coverage and stability.

Step 4: Place New Tile

While holding the edges of the tile, position it flat above the notched thin-set and gently drop it into place. Do not angle the tile in any way during the process to avoid shifting the ridges and negatively affecting the strength of the bond between the tile and floor. Once the tile is set, apply even pressure over the surface and lightly wiggle it into place. Make sure the tile is level and lined up with all the edges. Now, allow it to dry for 24 hours. While it’s drying, use a damp sponge to wipe away excess thin-set.

Step 5: Grout

Now the thin-set is dry and you are ready to grout the joints around your new tile. Using a rubber hand float, scoop a good amount of pre-mixed grout and work it into the joints using a sweeping arc motion. Always approach the tile diagonally at a 45° angle to ensure an even spread across the joints and prevent the float from digging into the joint.

Step 6: Clean Up and Dry

Clean off the excess grout with a damp grout sponge, then let the grout sit for about 15 minutes. It is completely normal to see a film or haze appear on the tile. To clear it, lightly wipe the surface with a damp sponge or towel. Wait at least 24 hours before applying pressure to the tile and you’re set! Your tile has been completely replaced and shows no signs of any previous damage. Not only did you learn a new skill, but you saved yourself money and time!

James marcus

Garden Courte is a blog written by [James Marcus], a passionate gardener and writer. She has been gardening for over 20 years and has a deep understanding of plants and how to care for them. In her blog, she shares her knowledge and experience with others, providing tips and advice on gardening, plant care, and more.

Share
Published by
James marcus

Recent Posts

DIY Turmeric Scrub for Hyperpigmentation

For all my beauties with dark inner thighs, armpits, bikini area and spots, etc, this…

1 year ago

Top 15 Cook Interview Questions and Answers

Are you a passionate cook aspiring to embark on a rewarding culinary journey? Whether you're…

1 year ago

What Color Walls Go With Grey Kitchen Cabinets [Schemes]

Discover the perfect wall colors to complement your grey kitchen cabinets, creating a harmonious and…

1 year ago

10×10 Kitchen Remodel Cost: Everything You Need to Know

Generally, a 10×10 kitchen remodel ranges from $15,000 to $45,000, but several factors could cause…

1 year ago

How Much Do Quartz Countertops Cost?

Sleek and durable, quartz countertops are the latest trend in kitchen and bathroom renovation. Comparable…

1 year ago

Australian IKEA Kitchen Design & Installation Costs

IKEA kitchens are designed to be as simple as possible to assemble and install yourself.…

1 year ago