How a finish is applied to cedar is as important for durability and good performance as is the finish-substrate combination chosen for the job. Finishes can be brushed, rolled, sprayed or applied by dipping.The application technique, the quality and quantity of finish applied, the surface condition of the substrate, and the weather conditions at the time of application can substantially influence the life expectancy of the finish.The application guidelines suggested here should be followed in concert with the manufacturer’s directions for the product.
Paints of all types such as vinyl-acrylic, modified-acrylic, and oil-based top coats are all suitable for cedar but test results show that good-quality 100%-acrylic formulations perform best.To achieve maximum paint life, follow these steps:
You are watching: Guide to Finishing Western Red Cedar
- On bare new or restored cedar, apply one coat only of water-repellent preservative (1% or less of wax by volume and content).Allow it to dry for the period of time recommended by the manufacturer. If the wood has been dip treated, a longer drying time may be needed. Do not paint before the solvent from the water-repellent preservative has evaporated because the paint may then be slow to dry, may discolor, or dry with a rough surface.
- Apply a good quality stain-blocking primer as soon as possible after the water-repellent has The primer coat is very important because it forms a base for all succeeding paint coats and should be used whether the top coat is oil-based or latex-based.Application rates recommended by the manufacturer should be followed.
- Apply the top coat over the If two top coats are to be applied, allow the first to cure for the period recommended by the manufacturer before applying the second. In cold or damp weather, allow extra time between coats.
Water-repellent preservatives should be used only on newly manufactured bare cedar, on restored bare cedar, or on cedar previously treated with the same type of product.Application of preservative by brush, pad, or roller followed by thorough back-brushing is equally effective. When cedar is treated after the structure has been completed, liberal amounts of the solution should be applied to all lap and butt joints, edges and ends of boards. Other areas vulnerable to moisture penetration, such as below doors and window frames, also need to be treated.
Read more : The Best Glues for Ceramic Repairs Tested in 2023
When used as a natural finish, the service life of a water- repellent is only one to two years depending upon the wood and the exposure.Treatments on textured surfaces generally last longer than those on smooth surfaces. Dip treatment prior to installation or repeated brush treatment to the point of refusal will enhance the finish durability.The more finish absorbed by the wood, the longer the service life.
If a water-repellent preservative is used as a pre-treatment before painting, apply only a single coat, and use caution to avoid excessive build-up.
Semi-transparent, oil-based penetrating stains may be applied by brush, spray, pad, or roller. Brushing will usually give the best penetration and performance. Spray or roller application followed by back-brushing is also an acceptable method of application.These oil-based stains are generally thin and runny, so application can be messy. Lap marks can be prevented by staining continuous lengths.This method prevents the front edge of the stained area from drying before a logical stopping place is reached. Working in the shade is desirable because the drying rate is slower. Stain that has been applied by spray without back-brushing is particularly prone to show blotchy patterns as it weathers.
Read more : How to Build a DIY Fire Pit With Gravel, Stones, and Walkway
Two coats of penetrating oil-based stain on textured cedar will provide longer service life than one coat, but only if the wood will accept the second coat. Stir the stain thoroughly during application to prevent settling and color change.Avoid mixing different brands or batches of stain.
Latex semi-transparent stains do not penetrate the wood surface, but they are easy to apply and less likely to form lap marks.These stains are film-forming and are not as durable as oil-based stains.
Solid-color stains may be applied to cedar by brush, roller, or pad. Brush application is usually the best.These stains act much like paint. One coat of solid-color stain is only marginally adequate on new wood. A prime coat with a top coat will always provide better protection and longer service.The best performance can be obtained if the wood is primed, then given two coats of stain.Top coats of 100% acrylic latex solid-color stains are generally superior to all others, especially when two coats are applied over a primer.
Unlike paint, a solid-color stain may leave lap marks.To prevent lap marks, follow the procedures suggested for semi-transparent penetrating stains.
Source: https://gardencourte.com
Categories: Outdoor
